大 美女100%露出奶网站,久久精品国产亚洲AV成人浪潮,国产乱子夫妻XX黑人XYX真爽,国产欧美一级内射7乀,精品无码污污网站在线观看

行業新聞

當前位置:首頁 > 新聞中心 > 行業新聞

如何提高制氮機的使用壽命?

來源:http://m.yczjsd.com.cn/   日期:2020-08-12   瀏覽量:0
TAG:山東制氮機,山東干燥機,山東螺桿鼓風機,山東空壓機,山東自動排水器

保養對于任何機器而言都是非常重要的,可以有效延長制氮機的使用壽命。那么如何提高制氮機的使用壽命,下面山東制氮機的小編為大家介紹下:

Maintenance is very important for any machine, which can effectively extend the service life of nitrogen generator. So how to improve the service life of the nitrogen generator, the following small edition of Shandong nitrogen generator is introduced for you:

除了保養之外,正確使用制氮機對于延長機器設備也是至關重要的。

In addition to maintenance, the correct use of nitrogen generator is also essential for the extension of machinery and equipment.

1、關閉所有的電源開關,包括制氮機和氮?dú)馊肟陂y及取樣閥,等待系統和管道完全泄壓結束。調節氧分析儀進行取樣并將減壓閥壓力調節到1.0bar,調節取樣流量計,將氣量調至在1左右即可,注意采樣氣量不宜過大,開始檢測氮?dú)饧兌取?/p>


20171218111431120.jpg

1. Turn off all power switches, including nitrogen generator, nitrogen inlet valve and sampling valve, and wait for complete pressure relief of system and pipeline. Adjust the oxygen analyzer for sampling, adjust the pressure of the pressure reducing valve to 1.0 bar, adjust the sampling flowmeter to adjust the gas volume to about 1. Pay attention to the sampling gas volume should not be too large, and start to detect the purity of nitrogen.

2、在壓縮空氣壓力要達到0.7mpa以上之后,才能打開制氮機的截止閥,同時要注意觀察吸附罐的壓力變化情況和氣動閥的工作能否正常進行。

2. The stop valve of nitrogen generator can only be opened after the compressed air pressure reaches above 0.7MPa. At the same time, the pressure change of adsorption tank and the normal operation of pneumatic valve should be observed.

3、再生塔壓力為零,均勻時兩塔壓力應接近原工作塔壓力的一半。

3. When the pressure of regeneration tower is zero, the pressure of two towers should be close to half of the original working tower pressure.

4、關閉整個系統和系統各部分,在制氮機吸附罐壓力達到0.6MPa左右時,觀察制氮系統是否正常工作。

4. Close the whole system and all parts of the system, and observe whether the nitrogen generation system works normally when the pressure of adsorption tank of nitrogen generator reaches about 0.6MPa.

在閱讀的小編為大家介紹的如何保持制氮機的相關內容之后,是否已經有所了解,想要更多的相關內容,可關注我們公司網站:http://m.yczjsd.com.cn/后期會呈現更多的精彩內容。

After reading the introduction of how to maintain the relevant content of nitrogen generator, whether you have any understanding. For more relevant content, please pay attention to our website: http://m.yczjsd.com.cn/ More wonderful content will be presented later.


上一篇:
下一篇:山東空壓機高溫停機的原因是什么?